Kinda Motor Frequency Converter Applied in Hoist Ppplications

1, Features of traditonal system
(1) The traditional system works at heavy load for long time, forward and reverse run frequently, the lifetime of the
system is short;
(2) High failure ratio.
(3) Low efficiency, the power factor is less than 0.8.
(4) The safety performance is bad.

2, Requests for frequency inverters (VFD)
(1) Big output torque at low frequency, it should run smoothly during working.
(2) Big overload capacity.

(3) Less failure ratio, run stably.
(4) Braking unit and braking resistor should be added.

3, Real application (Tower crane)
3. 1 system introduction

The hoist motor in the system is 55kW/380V, the load type is constant torque, to consider its heavy duty characteristic,
the frequency inverter should be selected two sizes higher as below:

3.2 system diagram

3.3 control logic

(1) The tower crane control system provide the forward and reverse signals, while MI1 and DCM closed, the tower
crane runs forwardly, and while MI2 and DCM closed, the tower crane runs reversely:

(2) The running speed of crane is controlled by ON/OFF conditions of MI3, MI4 and MI5, details as below:

(3) The inverter output a fault signal to the crane control system, while fault happen, the system will brake and stop immediately.

(4) There is an output FDT1 (controlled by F8-19 and F8-20) ON/OFF signal, while the inverter runs to the setting
frequency, this signal will control the brake to open, to avoid the reverse run happen.

3.4 autotuning

For this kind of heavy duty system, it is better to use Sensorless Vector Control (SVC) mode, it will get better output torque performance.
Before using SVC mode, please perform motor autotunning, do it as below steps:

1) Set F0-02=0 (keypad), set correct value of F2-01 ~ F2-05 (based on motor nameplate);
2) If the load can be removed from motor, please set F2-11=2 (Rotation autotuning, get better performance), if the
load cannot be removed from motor, please set F2-11=1 (Static autotuning). The keypad will display “TUNE”.
3) Press the RUN button, wait until the autotuning finish automatically.
4) Change the value of F0-01=0 (Sensorless vector control)

3.5 Parameters setting

3. 6 Problems faced during commissioning

(1) For KD330-09000T4, it needs connect additional braking unit and braking resistor to consume the regenerated
energy. The parameter of FA-04 is the braking threshold, the default value is 135%. The stand DC bus voltage is
540V, 540*135%=729V, that means while the DC bus voltage reach to 729V, the Braking unit will start work.
Sometimes, the fault of over voltage will happen, please reduce the value of FA-04 to avoid it.

(2) Cause the tower working distance is too long, during down running, the inverter works at regenerated status for long time, so the braking resistor should be selected bigger, to get better performance. In this system, it is
select as 4ohm, 10kW.

Shenzhen Kinda Technology Co., Ltd., established in 2012, is a technology innovation enterprise. Specializing in the production of export servo drive inverters permanent magnet synchronous motors, integrating product design, development and production. Our company is located in the urban area of ​​Shenzhen with convenient transportation. All products of our company adopt international quality standards, and the products are exported to overseas, and have many markets at home and abroad.

Our existing self-built factory covers an area of ​​10,000 square meters and has about 300 employees. Annual sales of 150 million US dollars, 60 percent of the products are exported to overseas.

The company has advanced and reliable laboratories, such as EMC electromagnetic compatibility laboratory, performance laboratory, and laboratory equipment such as 0.4KW~630KW. 100% of PCBA product line is tested by high-end automatic test system. The whole machine adopts fully automatic system for performance test, and the finished product is 100% qualified. At the same time as the quality inspection of the production process, we have CQC CE certification.

In view of high quality products and excellent customer service, we have established a global sales network. If your company is interested in any of our products or has an order intention, please feel free to contact us. 

Join us, enjoy the business.